QuietStove.com

Tuesday, March 15, 2011

Stove of the Week: MSR Rapidfire

OK, so this week's stove is a bit of a "sleeper" in the sense that it's not a stove that you would expect a lot from -- unless you knew better.  But you'll have to read on to find out what's so interesting about this week's stove, the MSR Rapidfire.

First, let's go through our usual run down of the stove, and then we'll get into some of it's unusual qualities.  So, what's with this thing called a Rapidfire?  Isn't it just a Whisperlite?  I mean seriously, just look at it.  It's a freakin' Whisperlite for crying out loud.

Or is it?  Take a look at the bottom of the burner column.  Hmm.  No priming cup.  OK, so what the Dickens is this thing?  Well, it is a close relative of the Whisperlite all right, but made to run on canister gas.
The Rapidfire was MSR's first entry into the gas stove market.  Prior to the Rapidfire, MSR was a liquid fuel only stove manufacturer.  When MSR saw how gas stoves were really catching on, they needed an entrant into the market.  How better to get there than to simply modify their existing "workhorse" stove, the Whisperlite?  Enter the Rapidfire.  Apparently, MSR was pretty paranoid about the volatility of gas as compared to liquid fuel; they really lengthened the fuel line which is odd when you consider that now the majority of MSR gas stoves mount directly on to the canister.

The stove itself is identical to the Whisperltie except for the aforementioned lack of a priming cup.
Instead of a priming cup, there's a threaded, knurled ring that holds the fuel line and legs in place.
At the end of the fuel line, there's a gas connector and valve rather than the open ended tube with aluminum block and catch-arm of the Whisperlite.
Now take a careful look at that connector.
Note the central pin.  It is this pin that depresses the Lindal valve inside the canister of gas.  I've seen these pins go missing.  No pin, and essentially you've got no gas.  Second, note the black rubber "O" ring.  This "O" ring must be in place for you to operate the stove safely.  Without the "O" ring, gas may leak which could be quite dangerous.

Speaking of gas, it's worth mentioning here that the MSR Rapidfire stove can use any standard threaded backpacking gas canister.  Originally, the Rapidfire used a cylindrical gas canister, but that canister had the same 7/16" UNEF standard thread as used on today's dome shaped canisters, so there's no problem with respect to finding fuel even though the Rapidfire is an older stove.  MSR discontinued production, to the best of my ability to discern, in 2001.

OK, so MSR needed a gas stove, so they pressed a modified Whisperlite into service, so what?  I mean does this Rapidfire have any redeeming features or is it just some kludgey attempt to not let all the other stove manufacturers run away with the gas stove part of the stove market?  Actually, the Rapidfire has several features that distinguish it from typical gas stoves, one of which actually makes the Rapidfire potentially pretty worth owning.  I'll get to that in a moment.
First, the Rapidfire, like its progenitor the Whisperlite, is a remote fueled stove.  In other words, the fuel is not directly attached to the burner but rather fuel is brought in via a fuel line from a remote source.  This does several things for us:  1) since there's no fuel tank under the burner, the burner is lower which brings us out of the wind.  2)  Also since the burner is lower, the stove is more stable.  3) Lastly and most importantly, since the fuel isn't local to the burner, we do not have to worry about heat radiating from the burner and overheating the fuel -- which means we can use a windscreen with complete impunity.  Use a windscreen the wrong way on a typical canister stove, and you could turn your stove from a domestic servant into a domestic terrorist.  Overheated canisters can and do explode.

Speaking of windscreens, here's a Rapidfire all set up with a heat reflector and windscreen, a very efficient cooking set up.

Now, I keep blathering about something special about the Rapidfire.  Let's take a closer look at the burner itself shall we?
Do you see that loop in the burner?  That's the fuel line.  That loop is referred to as a pre-heat loop (or generator).  The loop is exposed directly to the flame when the stove is in operation.  Fuel flows into that loop before it enters the burner, which greatly heats the fuel.  In a liquid fueled stove, that heat is what turns the liquid into a vapor so that it can be burned.

Well, that's just great, Jim, but we're working with gas here, so who really cares?

Are you?  Really?  Pick up a full canister of gas and shake it.  Hear that sloshing sound?  That's a liquid in there.

OK, great, it's a liquid in the can but it's a gas when it comes out of the burner, so I still don't care about that pre-heat loop; can we just move on?

Well, not so fast there.  Yes, you're right, it is a gas when it comes out of the burner.  Usually.  But what about cold weather?  Gotcha.  That's the problem with gas stoves.  They lose power when the weather gets below freezing because the liquefied gas in the canister won't vaporize properly.  Remember that pre-heat loop?  There's our answer.  In cold weather, we let the liquefied gas stay liquid, and we let the pre-heat loop vaporize it for us.  In that way, we don't care if it's cold or not.  We don't use the air temperature to vaporize our gas, we use the heat of the flame.

Uh, great Jim, but the connector attaches to the top of the canister, and all it's going to draw is gas off the top.  If there's no gas, we've got no fuel.

This is not a problem.  Just turn the canister over.  Note:  Do not invert the canister on a gas stove that does not have a pre-heat loop.  A serious flare up might result. 
The top of the canister is now the bottom.  That portion of the fuel that is in vapor form now acts to pressurize the canister, pushing liquid down, out of the canister, and down the fuel line.  The fuel stays in liquid form until it hits the pre-heat loop where the high heat causes it to change from liquid to gas.  The resultant gas comes rushing out of the burner, and baby you've got flame.  Note that the stove is in operation in the above photo.  When gas is fed in liquid form to the burner, the stove is said to be in liquid feed mode.  Note that I said liquid feed not liquid fuel.  The fuel will still be a gas at room temperature and pressure.  We haven't changed fuel; we've merely changed the form that the fuel is fed in.
Using a gas stove in liquid feed mode is an important capability for a couple of reasons:
1.  Normal gas stoves operate in vapor feed mode, that is the fuel is fed in as a vapor, and you have to rely on the ambient temperature to vaporize your fuel.  In liquid feed mode, you rely not on the outside temperature but on the heat of the flame.  Stoves in liquid feed mode will operate in colder weather than normal gas stoves.
2.  In normal gas stoves, the fuel is typically a propane-butane or propane-isobutane blend.  Propane, the gas that works best in cold, has a higher vapor pressure and burns off faster leaving you, toward the end of the life of the tank, with a tank full of your worst performing cold weather fuel. In fact, you may wind up with a canister that is still 30% full that you can't coax any gas out of because all the good propane has burned off and nothing is left but the lesser performing fuels.  In liquid feed mode, all the fuels are burned at a constant rate.  The fuel towards the end of the life of the canister is the same mix as at the start of the canister.  In liquid feed mode, you don't get such horrible "canister fade" like you do in vapor feed mode.

I normally recommend a cut off of about 20F/-7C for normal gas stoves -- and that's with using "tricks," having to put up with less-than-stellar performance, and potentially having fuel that you can't get to vaporize.  With a gas stove in liquid feed mode, you can easily go down to 0F/-18C without having to use a lot of tricks, with full performance, and without having a portion of your fuel being unusable.

In other words, with a gas stove in liquid mode, you get all of the convenience of gas without all the low performance and hassles associated with gas in cold weather.  Uh, couldn't I just use a regular liquid fueled stove?  Sure.  If you're comfortable with liquid fuel, go for it.  But consider this:  If it's really snowing hard and you need to cook inside your tent do you really want to use liquid fuel?  What happens if your priming gets a little out of hand?  With a gas stove in liquid feed mode, you get liquid fuel performance but without the danger of priming.  And of course you get all of the usual convenience of a gas stove.  One of those conveniences is simmering.  It's pretty tough to get the typical Whisperlite to simmer like this:
And that's without monkeying around with only filling the fuel bottle half full and only pumping a few strokes.  Easy, just about automatic simmering in other words.

Now, in all fairness, other remote canister gas stoves have pre-heat loops. Other remote canister stoves can operate in liquid feed mode.  What makes the Rapidfire a "sleeper" -- a stove you wouldn't expect much from but turns out to be a pretty good stove?  Well, take a look at the price tags on some of those stoves out there that are remote canister stoves and have pre-heat loops.  They're expensive.  The Rapidfire is an older, discontinued stove, most people haven't heard of it, and you can pick one up for a much more reasonable price than you can some of the current production stoves.  All the performance at a fraction of the price.  You heard it here on Adventures in Stoving.  :)  Also, the Rapidfire's fuel line rotates easily at the connector which makes it easy to invert the canister to put the stove into liquid feed mode.  The Rapidfire's more modern cousin, the Windpro, does not rotate easily at the connector.

Yep, the Rapidfire is a "sleeper," but don't underestimate this stove.  It's a lot of stove for the money.

Well, looks like the kettle's boiling.  I'd best get to that cup of hot chocolate before it gets cold.

Thanks for joining me on another Adventure in Stoving.

HJ

The MSR Rapidfire
What's good about it?
Able to operate in liquid feed mode
Economical
Can use a full windscreen with impunity even though it's a gas stove
Simmers well
Connector rotates easily for liquid feed mode
Quiet
Fairly compact
Reasonably powerful
Reliable
Stable
Efficient

What's bad about it?
The wire pot supports are difficult to get back into "true" if they get bent.  (so don't bend them!)
The fuel line is a little stiff particularly when compared to newer stoves like the WindPro.
A tad heavy when compared to newer stoves like the WindPro.

Overall, recommended.

42 comments:

  1. Amazing review as usual, not bland and interesting to read, Keep up the good work!

    ReplyDelete
    Replies
    1. Before i knew much about these gas stoves i bought 4 tanktop models,3 of the same type on ebay and one locally sourced.

      They all worked great but i wanted a remote feed version cheap.
      It took a while but i finally found one at cash converters for $15(normal price of $50).
      The advantage(unkown by me at the time) is this remote feed stove has a generator loop to allow it to work with liquid feed.

      I swear by this stove.its very heavy compared to minimilist tanktop stoves but the weight is a small price to pay for safety and versatility.

      Now im more interested in liquid fuel as ive just finished a 7 month bush camp and fuel is horrifically expensive in NZ.

      One outdoor shop in Queenstown had a 1 litre bottle of meths for $16.99.

      I thought it was a joke but they said its thier normal price and have never sold one-the local supermarket sells the same stuff for $5.27.

      Even meths gets dam expensive ling term when your living on less than $200 a month

      Delete
  2. Jim, when I bought my Whisperlight, a friend of mine bought the Rapid Fire. Of course we had the usual two-guy banter over boiling water..."those gas canisters are heavy", "a liquid fuel stove is a man's stove", etc. Fact is, he was always eating before me! Great info on the liquid feed mode too. Thanks

    ReplyDelete
  3. Hey, Andy, you're welcome. As I say, "the Rapidfire is a 'sleeper,' but don't underestimate this stove. It's a lot of stove for the money." Of course nothing wrong with the Whisperlite either. A four ounce (113g) canister of gas costs $5.79. The same amount of Coleman Fuel for a Whisperlite? $0.39. That's right thirty-nine cents. Can you say, "SUPER ULTRA CHEAP!?" :) HJ

    ReplyDelete
    Replies
    1. HJ


      Coleman fuel? or more correctly WHITE GAS,is only available at bunnings and very few other places.
      Bunnings calls it "sgellite" and it is a tad under $10 per litre-not an option in NZ
      Even Kerosine is $5something a litre-not really a cheap option.

      Delete
  4. Hi there, having managed to find a msr rapidfire, I now find it near impossible to track down a maintenance kit. Any suggestions please?

    ReplyDelete
  5. Hi, Dawn,
    I believe there's a Rapidfire maintenance kit on eBay right now. However, gas stoves are usually very low maintenance. Is there something in particular wrong with yours?

    HJ

    ReplyDelete
  6. Hi there, nothing wrong with the stove, however, being some fifteen years old I wondered if it was due for a service. Mind, it still runs fine.

    ReplyDelete
  7. I myself probably wouldn't replace the jet (nozzle) unless there were a definite problem with it.

    It wouldn't hurt to replace the "O" ring in the attachment to the fuel canister. If it's hard or cracked, definitely replace it. MSR may still stock that "O" ring; you could call them and ask. You could also try to get a maintenance kit on eBay.

    Good luck and happy stoving,

    HJ

    ReplyDelete
  8. Hi Jim. I've been reading your hiking blogs for over a year and the Jan Jacinto Bullitin Board. I have a rapidfire but have been unable to rotate the line. Which coupler rotates? The one on the Valve ot near the stove?
    Thanks
    CK

    ReplyDelete
  9. Chris, the point at which a Rapidfire will rotate is where the valve and connector attach to the fuel line. If you look at the photo with a close up of the connector, the point at which it rotates is to the left of my thumb but before the canister connector.

    HJ

    ReplyDelete
  10. Excellent information here. I have had several liquid (white gas) stoves and now have an upright canister stove. I see this Rapidfire may be the solution to the cold weather problem. What a great idea. Thanks so much for you webpage.

    ReplyDelete
  11. You're welcome. I'm glad the info is helpful.

    HJ

    ReplyDelete
  12. This comment has been removed by the author.

    ReplyDelete
  13. I deleted my last entry as it regarded whether my RF would take other canisters. It does.

    I would like to add that it's a better idea to rotate the valve without the canister attached: You might strip the threads and create a leak. Adjust the angle of the valve with the canister off. Also, my valve does require a bit of work to rotate. I'd tried with a gentler hand as to not do damage, but did finally get it to move. So glad that little stove still works. I have an Internationale, as well. They're a pain, but of course very versatile. That thing'll burn just about anything short of earwax...

    ReplyDelete
  14. Hi, Adam,

    Yes, the RapidFire will work with any standard (7/16" UNEF) threaded canister.

    The coupling on my RapidFire turns pretty freely, and I turn it at the coupler. I'm not worried about stripping the threads (I don't think they're THAT fragile), but individual stoves may vary.

    HJ

    ReplyDelete
  15. I just pulled our RapidFire stove from the basement…It was waiting patiently for our children to get old enough to go backpacking.
    I read the owner’s manual and your fantastic blog, hoping to re-familiarize myself with the stove for an upcoming overnight with my 5-year-old son.
    I never realized what a gem-of-a stove we have...so thanks for the write-up.
    I am curious about "canister fade" and your comment,"In liquid feed mode, all the fuels are burned at a constant rate." I wonder if it is best to always use the canister inverted? I see that the WhisperLite Universal even comes with a Canister Stand to do this easily.

    ReplyDelete
    Replies
    1. It never hurts to run a stove in inverted mode, but if temperatures will consistently be above 50F, it won't matter much. Preferential burning (where the propane burns off at a faster rate than the other components in a gas canister) always occurs when you run with the canister upright, but it doesn't hurt anything in warm weather. It's when it's cold that you really need to run with the canister inverted.

      HJ

      Delete
    2. Are there adaptors to use "regular" propane (less expensive) bottles with the RapidFire?

      Delete
    3. Yes, there are adapteres to run with regular propane. The adapters are heavy, but if you're car camping or taking short trips, then it's no big deal. I have such an adapter featured here on the site. See 100% Propane for Backpacking II.

      HJ

      Delete
  16. I just picked up a Rapidfire at the Goodwill but it is missing the Elbow Screw. I tried Calling the company this morning but the phone numbers are no longer in use. Can I get this at a local hardware store or is there a newer number?

    Thanks,

    Glen

    ReplyDelete
    Replies
    1. Glen,

      I'm not sure what you mean by "elbow screw." Do you mean the piece that holds the fuel hose onto the burner? it also holds the legs onto the stove. I doubt that you can still buy the piece from MSR; the Rapidfire has been out of production for a very long time. You could a) try to get a compatible piece at a hardware store or b) use the priming cup from a Whisperlite. The priming cup should have the same threads. I would call MSR and ask if the threads are compatible. If they don't know, post a comment to that effect here, and I'll see if I can dig out a Rapidfire and check for you. The number I have for MSR is 1-800-531-9531.

      HJ

      Delete
    2. This is the screw that goes in the bottom and holds the fuel hose up into the stove. I didn't realize it was so old of a unit. It still burns well. Thanks for the info. I called the 800 # and it say it is "Cascade Designs". Does that sound right to you? I called too early to talk to anyone and just got a recording.

      Delete
    3. Glen,

      OK, that's what I thought you meant; I just hadn't heard it called an "elbow" screw before.

      The RapidFire was discontinued in the 90's as I recall. It was supplanted by the WindPro, but the RapidFire really is a good stove. Take care of it, and you should have DECADES of good service.

      Cascade Designs is the parent company of MSR. They probably just have one customer service number for all the companies under Cascade Designs (MSR, Thermarest, etc.). In other words, you've got the right number.

      HJ

      Delete
  17. Cool. Thanks again. I did go to the hardware store and picked up a 12mm(1.25 thread)bolt. I took it home and cut it down to the right size with my Dremel tool. It works GREAT. The stove works just fine and I am excited to take it out on a trip and use it. Thanks again for all your help.

    - Glen

    ReplyDelete
    Replies
    1. Excellent, Glen. Glad you've got it working. I think you'll find that it's really a super stove.

      HJ

      Delete
  18. Hi Jim, Hope you don't mind me asking but does the rapid fire have the same number of spreader rings as the whisperlite? I need a replacement set for my rapid fire but its second hand and I think some rings maybe missing. Thanks.

    ReplyDelete
    Replies
    1. Alan,
      To be honest, I'm not sure off the top of my head. I would think that the RapidFire has the same number of rings, but I haven't checked lately. Let me check some time this week when I get a chance. We moved recently, so my stoves aren't organized just yet. It may take a bit to dig it out. If you don't hear from me by this Sunday, feel free to post a little reminder here.
      HJ

      Delete
  19. RapidFire has a long fuel line because in days of olde, MSR used tall skinny "hair spray" cans of fuel. This appears in the advertising.

    ReplyDelete
    Replies
    1. Ah, yes, I remember those. They were 100% isobutane. I still have a couple in my collection. Makes sense.

      HJ

      Delete
  20. Thanks for the informative article on the Rapidfire.

    I picked mine up back in the very early 2000s to use as a supplement to my liquid fueled stoves, but until I read the above I did not fully appreciate the gem I'd apparently picked up, seeing that it had been in the cut price bin as run out item at the time.

    I also did not know that the connection was supposed to rotate, but try as I might I do not seem to be able to get mine to budge and fear that I may end up damaging it if I apply to much force.

    So any further hints as in how to free this up, like clockwise - anticlockwise etc would be appreciated?

    Thanks David

    ReplyDelete
    Replies
    1. David,

      It's possible that it's become frozen over time. You were right not to force it. If it breaks, that's the end of it; spare parts are no longer available.


      Anti-clockwise vs. clockwise shouldn't matter, but maybe I'll take mine out and have a look. You could try a very minimal amount of some kind of lubricant, taking care NOT to get any lubricant inside the fuel line or connector. Lubricant inside could clog the stove which would be a hassle to correct.

      HJ

      Delete
    2. That's excellent, David. Glad to hear it. I actually like the RapidFire even though it's not quite up to modern standards. None-the-less it is a very stable and versatile stove. By no means is it outclassed by more modern stoves except perhaps in weight (it's a bit heavy by today's standards, but not horribly so). I hope it gives you good service.

      HJ

      Delete
  21. G’day JH

    Thanks for the rapidfire (pun intended) response to my question.

    I have always felt that the braided fuel supply line / hose on my sample appeared to be somewhat slightly offset and that is also very stiff overall, the result being that the canisters never wanted to sit very flat.

    I took a picture of the valve/connection assembly and colour coded the various components based on the descriptions from the instruction book (yes I know that it’s sort of tragic that I still have this along with the original box too) in an effort to identify exactly what component is supposed to rotate.

    I will try and add a link to it here: https://scontent-lax1-1.xx.fbcdn.net/hphotos-xta1/v/t1.0-9/11108402_841348239282732_3891041750743806215_n.jpg?oh=d9ca1689eaf5451af2d490b446bd734a&oe=562FA42D

    [img]https://scontent-lax1-1.xx.fbcdn.net/hphotos-xta1/v/t1.0-9/11108402_841348239282732_3891041750743806215_n.jpg?oh=d9ca1689eaf5451af2d490b446bd734a&oe=562FA42D[/img]

    If you can see the image the, as I understand it the item labelled Valve Body Assembly is the part that should be able to rotate, where it connects to the braided supply hose and this is also the point I should attempt to lubricate it?

    Again many thanks for your assistance.

    David

    ReplyDelete
  22. ..... JH or maybe try this link to see my image.....

    https://goo.gl/photos/sX96w6c81b8e3QseA

    I'd usually use a photobucket link but due to server issues I cant access this during working hours

    David

    ReplyDelete
  23. JH….. Success

    Well I ended up taking the stove down to the workshop this morning, and after getting one of our water heaters set to deliver 90°C (194°F) I ran the hot water over the connection / valve for a good 5 plus minutes, with it still hot I worked some O-ring grease (also care of the workshop) into the joint for several minutes. Then put the connection / valve under the hot water again for another good 5 plus minutes.

    With not letting it cool down I quickly worked a little more O-ring grease into the joint, then by using a cloth to gently clasp the collar of the braided hose with a pair of pliers to both protect the hose and to avoid the burning my fingers on the hot brass, I proceeded to firmly but gently attempt to turn the Valve Body Assembly in both directions, gradually I noticed that it was finally beginning to stiffly turn.

    While it was still cooling I continued to both try and work more O-ring grease into the joint and also rotate the Valve Body Assembly.

    So fast forward to some 2 hours later and the components haves now cooled to room temperature (about 20°C) and the Valve Body Assembly still appears to be turning, it’s by no means freely spinning but that can only be a good thing, I hope to grab a canister on the way home from work and do a submersed leak test tonight or at least on the weekend.

    All in all I’m rather happy with today’s outcome and even though I still do covert the ownership of a Whisperlite Universal someday, for now my rediscovered Rapidfire is ready (and hopefully willing) for action.

    Thanks again for your blog, for if not its existence I may have never known about my Rapidfire’s additional potential.

    Cheers David

    ReplyDelete
    Replies
    1. Excellent! I can only imagine that with age things seized up. Glad to hear you worked them loose. Hopefully your dunk test will go well.

      HJ

      Delete
    2. Oops just realised I've been typing JH and not HJ, anyway I will let you know how the dunking results go,

      Cheers David

      Delete
    3. No worries. I figured it was me that you were talking to. Best of luck on the test. Should be fine.

      HJ

      Delete
    4. HJ

      Got a canister last night, however due to prior commitments had to wait until this morning (AU time) before I was able to do a pressurized dunk test, I'm glad to report, no bubbles, so no troubles.

      Cheers David

      Delete
    5. G'day HJ

      I did a quick test firing tonight (AU time), which leads me to one final question, regarding what is the normal length of time it takes to expend the residual gas in the fuel line once the valve is closed.

      It seemed fairly long, to the point where I was starting to think that the valve was not fully closing, but as It's been about 5 years since I used it, I may have simply forgotten about this apparent operational quirk.

      Cheers David

      Delete

My apologies to real people, but due to Spammers I have to moderate comments. I'll get to this as rapidly as possible but do understand that I like to hike and there's no internet in the wilderness. Take care and stove on!